Make your own Bathtub? - DIY Home Improvement Forum
网页2007年4月6日 — Ron6519 said: And no, you cannot make your own bathtub. You can attempt it, but you will not succeed. Ron. I beg to differ. The more we get into concrete countertops, the more the industry is testing the limits of what was thought to be workable. This book: Concrete at Home. By: Fu-Tung Chen, with Eric Olsen.
How to attach bathtub side panel - DIY Home Improvement Forum
网页2020年8月6日 — Another idea: drill some holes in the flanges of the frame and epoxy some pegs onto the panel. Actually, do the reverse: glue the pegs onto the panel and then use them—paint the tips—to locate the holes on the flanges. rmk9785e. Reply Like. b.rooster4321. 528 posts · Joined 2020. #8 · Aug 8, 2020.
Adhering PVC trim to bathtub? - DIY Home Improvement Forum
网页2019年4月3日 — This was per the installation instructions for this type of tile. But I feel like I'm not going to like the finished appearance of a big 1/4" bead of white silicone along there. So we're looking at adding a piece of PVC trim or quarter-round and the siliconing the top and bottom of that, where it meets the tub and where it meets the floor.
Add shower plumbing to an existing bathtub - DIY Home …
网页2011年5月15日 — Add shower plumbing to an existing bathtub. One of our bathrooms has a tub, but no shower head. The walls around the tub are tiled about two feet up and the faucet and knobs are set in the tiles, at one end, within 6-12 inches of the top of the tub. The wall above the tiles is covered with wallpaper, so I am assuming sheetrock behind.
Type of mortar: setting bathtub | DIY Home Improvement Forum
网页2019年3月24日 — It is a cheap easy way to add a lot of extra support. Plastic (Vikrell, Fiberglass etc...) tubs can weaken a little over time and flex. Just put down tar paper if you are worried about squeaks. We are usually putting down new sheet vinyl floor with a tub replacement. Most of time vinyl goes down including under the tub.
Apron bathtub framed for tile? - DIY Home Improvement Forum
网页2012年1月10日 — I was thinking of building the wall 2 or 3 inches below the top if the apron. That way once you install the cement board and tile you would have just a little bit of the apron sticking out above, giving the illusion of a drop in tub. My concerns are building the wAll and the tub flexing causing the grout to crack.
Drywall behind bathtub? - DIY Home Improvement Forum
网页2010年9月19日 — Drywall goes down to within 1/2" of the flange on the tub. Wonder board (cement board) on top of the drywall. That give you the extra thickness for your bullnose tile on the edge. Drywall should not sit directly on the tub as it can "wick" moisture and will eventually fall apart (even green board) if the tub is not kept caulked properly.
Floor load w/ bathtub - DIY Home Improvement Forum
网页2008年12月27日 — Floor load w/ bathtub. I'm going to be installing a bathtub on the second floor of my house in a newly built bathroom. The floor has 2x10 joits, 16oc. The span is about 12 feet. The tub will be about four feet from the rim. I want to put in a 300 pound cast iron tub with claw feet. Now I know with water and humans, this presents a pretty good load.
US supplier for L or P shaped bathtub? - DIY Home Improvement …
网页2015年5月26日 — I thought about the curved tubs, but I generally don't like shower curtains. Reply Like. Oso954. 11192 posts · Joined 2012. #6 · May 27, 2015. While not exactly a P or L, the Duravit Paiova tub might work for you. It is a tapered tub with extra shoulder room.
Help with a Mobile Home bathtub repair - DIY Home …
网页2019年11月16日 — I am a simple DIY person. I am needing to replace a bathtub faucet in my front bathroom. I know how to do it. My problem is finding good materials to work with. The faucet is a single operating faucet/shower. Offset. 8 inch. The original faucet lasted almost 20 years. If finally gave up the ghost and started leaking.